With the exploration and innovation of company people, gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel.
AISI 4140 alloy steel can be tempered at 205 to 649C (400 to 1200F) depending upon the desired hardness level. The hardness of the steel can be increased if it has a lower tempering temperature. For example, a tensile strength of 225 ksi can be achieved by tempering at 316C (600F), and a tensile strength of 130 ksi can be achieved by tempering at 538C (1000F).
Tempering temperature of 4140 alloy steel can be from 204-649 C (400-1200F) after normalizing and oil quenching, and the corresponding Rockwell hardness can be obtained. Forging. Material 4140 forging temperature is about 1232 C (2250 F). Welding of 4140 Steel
TimkenSteels 4140HW grade is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier cross-sections. You find 4140HW in a variety of bar and tubing applications in quenched and tempered conditions. Yield strengths range from 110 ksi through 140 ksi, but we can temper it to other strength levels.
TENSILE - YIELD STRENGTH OF STEEL CHART. Steel Alloy 1040 - Annealed (@785 C) 355 (51.3) 520 (75.3) 30.2 Steel Alloy 1040 - Normalized (@900 C) 375 (54.3) 590 (85) 28.0 Steel Alloy 4140 - Annealed (@815 C) 417 (60.5) 655 (95) 25.7 Steel Alloy 4140 - Normalized (@870 C) 655 (95) 1020 (148) 17.7 Steel Alloy 4140 - Oil-quenched and temperedyield strength of 4140 steel
Introduction. The AISI 4140 cold finished annealed chromium-molybdenun alloy steel can be heated using various methods to yield a wide range of properties, hence it is often used as stock for forging as it has self-scaling properties. AISI 4140 is capable of resisting creep in temperatures up to 538Cyield strength of 4140 steel
AISI 4140 Steel, annealed at 815C (1500F) furnace cooled 11C (20F)/hour to 665C (1230F), air cooled, 25 mm (1 in.) round yield strength of 4140 steel
sae 4140 steel pricebing.comforged aisi 4140natural-elements-online.comaisi 4140 forged barnatural-elements-online.com2:27MECE 5397 - Surface Temperatures Effect on the Strength of AISI 4140 Steelyoutube.comYield Strength Of 4140 Steel videos
4140 steel is chromium, molybdenum, manganese steel with good toughness, impact resistance and fatigue strength. 1045 has slightly increased tensile strength and yield strength numbers than 1045 as a result of a slightly higher carbon content.
4140/4150 (modified) Hot Roll, Heat Treated, High Strength Alloy. Kromite #3 is a modified 4140/4150 steel. Typical hardness is Rockwell C 28/34. This chromium and molybdenum based alloy is electric furnace melt, vacuum degassed, stress relieved, and machine straightened. It is offered in the hot roll, heat treated condition. Typical tensile strength is 156,000 PSI.
4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved
AISI 4140 Alloy Steel is chromium, molybdenum, and manganese containing low alloy steel. It has high fatigue strength, toughness, abrasion resistance, and torsional strength. AISI 4140 is 1% chromium molybdenum medium harden the capability basic cause excessive tensile metal.
eFunda: Properties of Alloy Steel Alloy Steel AISI 4140. Alloy Steel Alloy Steel AISI 4140 Directory | yield strength of 4140 steel Yield Strength (MPa) 655.0 : Elongation (%) 17.7 :
The following is a comparison of 4130 grade steel and 4140 grade steel. This information may be useful for machining purposes and as a resource for purchasing 4130 and 4140 steel. Chemical Properties The chemical properties of 4130 and 4140 steel are similar aside from differences in Carbon and Manganese concentrations.
HIGH TENSILE STEEL AISI 4140 AISI 4140 Chrome - Moly High Tensile Steel, generally supplied hardened and tempered to Condition T in sections up to 100mm, with a tensile strength of 850 1000 MPa and aiming for this strength range in larger sections. It offers a very good balance of strength, toughness and wear-resistance.
AISI 4140 steel is a low alloy steel containing chromium, molybdenum, and manganese. It is widely used across numerous industries and is an excellent material choice due to its toughness, high fatigue strength, and abrasion and impact resistance. Not many grades can match the versatility and usefulness of 4140. 4140 Grade Designation
AISI 4140 Steel Bar, Steel Plate, Flats Supplier, Stockist and Exporter. AISI SAE 4140 alloy steel is a chromium molybdenum alloy steel specification widely used in general purpose high tensile steel for components, like axles, shafts, bolts, gears and other applications.
4140 steel is a low alloy steel commonly used in structural members and mechanical components. It is composed of Chromium, Manganese, Carbon, Silicon, Molybdenum, Sulfur and Phosphorus submerged in a matrix of Iron.
Property Data; This page displays only the text of a material data sheet. To see MatWeb's complete data sheet for this material (including material property data, metal compositions, material suppliers, etc), please click the button below.
What is 4140 Steel? AISI 4140 steel also can be called DIN 1.7225 and JIS SCM440 steel. 4140 alloy steel has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state.
AISI 4140 and 4150 steels offer a high resistance to fatigue, improved toughness, impact resistance, and torsional strength. Not all AISI 4140 and 4150 materials are made to the same standards. Material purchased from Specialty Steel is also Machine Straightened and Stress Relieved.
control of steel temperature uniformity and sufficient holding times to limit stresses and prevent cracking. Welding Welding of 4140PH requires exceptional care due to the high sulfur level. High pre postheating temperature should be used (350C - 660F) to avoid cold cracking. Industeel Trademark
4140 Heat Treated is a chromium-molybendium alloy steel. 4140 HT is the most commonly used high tensile steel with endless applications including everything from gears and pumps to various applications in the automotive and construction industry. 4140 HT has a medium hardness of 28/32 HRC.
4140 High Tensile Steel 4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting mechanical properties.
4140 Alloy Steel Flat is an cold drawn annealed steel of relatively high hardenability with its chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. 4140 Alloy Steel Flat responds well to heat-treatment and is relatively easy to machine in the annealed condition. 4140 Alloy Steel Flat has good strength and wear resistance yield strength of 4140 steel
4140 PREHARD is heat treated to a medium hardness (HRC 28/32) and is designated as 4140 HT. 4140 annealed is supplied in the soft condition and can be hardened to RC 40. 4140 HT is supplied in many forms such as hot rolled or turned, ground and polished rounds and DCF plate to be used as a holder material for high strength structural components.
4140 Alloy Steel Round, is an cold drawn annealed steel of relatively high hardenability with its chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. 4140 Alloy Steel Round responds well to heat-treatment and is relatively easy to machine in the annealed condition. 4140 Alloy Steel Round has good strength and wear resistance yield strength of 4140 steel
SAE-AISI 4140 steel is an alloy steel formulated for primary forming into wrought products. 4140 is the designation in both the SAE and AISI systems for this material. G41400 is the UNS number. It can have a moderately high tensile strength among the SAE-AISI wrought steels in the database.
For all critical applications, verify to the applicable industry or requisite material / steel standard. AISI Carbon Steel Mechanical Characteristics Table Chart Yield, Tensile, Hardness AISI 3140 - AISI 9310
Yield strength uses the slope of the initial elastic region of the stress-strain graph to determine a 0.2% offset along the curve; ultimate tensile strength is essentially the maximum stress yield strength of 4140 steel
Materials Alloys Steel Alloy Steel AISI 3140 Materials Alloys Aluminum Alloy Wrought AA 6151 Materials Alloys Aluminum Alloy Wrought AA 6066
Both SAE-AISI 4140 steel and SAE-AISI 4340 steel are iron alloys. They have a very high 98% of their average alloy composition in common. For each property being compared, the top bar is SAE-AISI 4140 steel and the bottom bar is SAE-AISI 4340 steel.
what is the yield strength of 4140 steel
You may also leave contact information, we will contact you as soon as possible!